You will find this post useful in case you are looking for a way to make your computer boot from a USB drive, instead of booting from hard drive as it normally does. In this post you will be learning the steps to enable USB boot in BIOS settings, so that you can make your computer boot up from a Windows recovery drive.
Use the up or down arrow keys to scroll through the list of hard drives and press Space to select the drive. Install the RAID driver using the F6 installation method To install the Intel® Rapid Storage Technology (Intel® RST) driver during operating system setup, follow these steps. Use a USB floppy drive or create a slipstream. Apr 01, 2016 HPE USB Key Utility for Windows. By downloading, you agree to the terms and conditions of the Hewlett Packard Enterprise Software License Agreement. Note: Some software requires a valid warranty, current Hewlett Packard Enterprise support contract, or a license fee.
Enable USB Boot in BIOS
In general, most computers boot from their hard drives where the computers operating system is stored. While some newer computers may provide a choice for booting from the USB drive during startup, others may not do so.
Follow the steps below to check whether your computer can boot from a USB drive and make it boot from a USB drive, in case it is not set that way.
1. Plug a Bootable USB Drive into the USB port of your computer.
Note: You can skip steps 1 ~ 4 and start from step 5 in case you are certain that your computer is not set up to boot from a USB drive.
2. Remove all other portable media like CD, DVD from the computer and power it on.
3. If the computer is configured to automatically boot from the USB drive, you will see a screen that says “Automatic boot in 10 seconds…”
4. If you believe the computer is trying to boot from the hard drive, you’ll need to manually configure it to boot from the USB drive.
5. Wait for a safe point where you can reboot the computer.
6. Reboot the computer and watch the screen for instructions on which key to press for getting into the boot device selection menu, or “BIOS setup”.
The screen messages will say something like Press [XXX Key] to Enter Setup or BIOS SETUP. You will only have a few seconds to read the instructions on your screen. Reboot the computer again, in case you missed the opportunity to read the instructions properly.
7. Use the suggested Key to get into BIOS settings
Please note that you may need to press the suggested key more than once to enter BIOS. You should not hold down the key (just press and release). Also, do not press the key too many times as you may end up locking the system or
generating system errors.
generating system errors.
8. Go to the Boot Tab of BIOS setup utility and use the keys to make your computer boot from the USB drive first in the boot sequence.
Note: In general, the BIOS on most computers will list the USB boot option as Removable Devices or USB. However, on some computers USB boot option might be listed under Hard Drive. Make sure to check under hard drive option, in case you are having problems locating the USB boot option.
9. Save the changes and exit from BIOS utility.
10. Your computer is now ready to boot from USB drive
When you enable boot from a a USB device, what you are essentially trying to do is to make your computer run from the operating system that is installed on the USB device, instead of running from OS installed on the hard drive.
For computers using Windows operating system you can easily create a Bootable Windows USB drive or a Windows USB Recovery Drive. These will allow you to boot a computer from the USB drive whenever your Windows computer is facing problems and requires troubleshooting.
The F6 installation method allows you to install a third-party mass storage driver during Windows* setup. The chart below shows the circumstances in which you must use the F6 installation method during an operating system installation.
Operating system | Total drive volume | F6 installation method |
Windows 8* | Any size | Recommended but not required1 |
Windows 7*, Windows Vista* | Less than 2 terabytes | Recommended but not required1 |
More than 2 terabytes2 | Required | |
Windows XP*, Windows Server 2003* | Less than 2 terabytes | Required |
More than 2 terabytes2 | Required |
1 Windows 7 and Windows Vista both include drivers for RAID/AHCI during installation.
2 For Intel® Desktop Boards, you must first enable UEFI in the BIOS when using total drive volume greater than 2 terabytes. For non-Intel motherboards, refer to the motherboard documentation to verify this requirement.
2 For Intel® Desktop Boards, you must first enable UEFI in the BIOS when using total drive volume greater than 2 terabytes. For non-Intel motherboards, refer to the motherboard documentation to verify this requirement.
General information
Troubleshooting
Related topic |
Microsoft Knowledge Base article: Limited original equipment manufacturer (OEM) driver support is available with F6... |